Форум обсуждение

Send message

[ +7-981-8529467 (Санкт-Петербург)

t.me/os2_guru

 
Update

 
Applications

 
Advantages:

 
For developer:

 
(Пайпы программ)

 
Companies:

 
History:

 
(Бонусы)

 
Advice:

 
(Барьеры и решения)

 
Technologies:

 
(Применение в науке, лаборатории, ..)

 
Solutions

 
New eComStation:

 
Future:

 
(Ссылки на другие сайты)

 
(Картинка дня)

 
OS/2 artefacts:

 
Gadgets:

Hardware > Motherboards ASUS M2N32 WS Professional Homepage: Specification

?>

ASUS M2N32 WS Professional

Mark: Very good

This computer is a new home built assembly and not fully tested.

My Hardware Setup on this motherboard

• CPU: AMD Athlon 64 X2 6400+
• memory: 4x1g DDR667
• Video: ATI All in Wonder X600 series
• CD/DVD rw ide
• HDD 1xide, 4xSATA
• no floppy drive, (USB floppy available if required)
• no telephone modem, (available, but internet and lan is through a DSL modem and Router)

Initially, just as a test,I installed eComStation 2.0 RC7 Silver into the above configuration. Booting from the CD I used the menu with my own values, The hardware was identified correctly and in the right quantity (USB controllers), I left the "Safe mode, modern hardware" alone and did not select ACPI/APM. The only other changes I made were to select VGA instead of SNAP/Panorama, re-assign the reserved drive and deselect the hard disk integrity check and started the Installer. Installation was done using the Advanced Install option and "migrated/no format" into a logical partition (previously prepared by dfSee as a bootable JFS voume and formatted by booting to the CD's command line). The only the only Installation hardware selections I made were, uniaud, video as VGA and added a serial port. The network installation correctly identified the network adaptor and offered to install Nikki's NETH.OS2 driver. The only other selections I made were adding some additional apps and changing some paths, everything else was the default selections.

When I started the installation, everything went smoothly until the network installation where the installation of the "IBM dialup Tools" hung. I reformatted and during the Installation selections did as above and de-selected the IBM Dialup Tools. The installation went smoothly with no other problems: the desktop came up and sound came out of the speakers, FireFox connected to the internet. The full SNAP-os2-318 installed and configured correctly. Using the "Post Installation Tasks" the ACPI selected the switches /SMP /APIC and installed.

The eCS2silver installation has yet to exhibit any problems other than PSCOM.SYS hangs the boot process and ACPI occasionally performs a warm re-boot rather than a complete shutdown/power off. The operating system is still basically as installed and not tweaked or customized There have been no issues with what few applications I have installed.

Circumstances (my working machine starting to fail), caused me to cheat and clone eCS12mr and applications onto this computer. The only changes I had to make were to a change from the old 3com network adapter to the Nvidia one, and a major cheat to get Audio I replaced the old \MMOS2\*.* completely by deleting it and xcopying over the eCS2silver \MMOS2\*.* completely and modified/replaced the eCS12 config.sys with those of the silver installation. Everything has worked as before.

I have yet to experiment with the other features of this motherboard or ensure that either of my eCS systems are properly configured for this hardware.

******************************************

Information is sent by: Jim Hughes -- 2010-05-27 18:10:52

[GoogleAdv]

Comment this note (add comments, don't expect that other users will reply or join discussions here)
	Your Name: Your E-Mail: CODE:
Your Comment:

eCo Software doesn't drill oil or gas, we don't cultivate bananas. eCo Software is developing applications and exporting this products to Europe. We pay taxes and feed pensioners, teachers and policemen.

 
For dummies

 
Reviews